P/N: AD382-2
Price: $69.50
Eligible On: Cessna 180 and 185
STC: N/A
FAA/PMA: N/A
Material: 4130
Purpose: Direct replacement for Cessna P/N NAS382-2
Installation: Same as original part
Misc. Info: Rudder/Tailwheel Steering/120/140 Aileron
More
Author: Stacy Chalmers
Cessna Retainer, Control Cable
P/N: AD1650042-3
Price: $144.25 each
Eligible On: Direct replacement for Cessna P/N 1650042-3
STC: N/A
FAA/PMA: N/A
Material: Cadmium Plated 4130
Purpose: Mixture and/or throttle assembly
Installation: Same as original part
More
Cessna Retainer, Control Cable
P/N: AD0750614-3
Price: $144.25 each
Eligible On: Direct replacement for Cessna P/N 0750614-3
STC: N/A
FAA/PMA: N/A
Material: Cadmium Plated 4130
Purpose: Mixture and/or throttle assembly
Installation: Same as original part
More
Cessna Retainer, Control Cable
P/N: AD1650042-4
Price: $144.25 each
Eligible On: Direct replacement for Cessna P/N 1650042-4
STC: N/A
FAA/PMA: N/A
Material: Cadmium Plated 4130
Purpose: Mixture and/or throttle assembly
Installation: Same as original part
More
Cessna Retainer, Control Cable
P/N: AD0750614-5
Price: $82.50 each
Eligible On: Direct replacement for Cessna P/N 0750614-5
STC: N/A
FAA/PMA: N/A
Material: Cadmium Plated 4130
Purpose: Mixture and/or throttle assembly
Installation: Same as original part
More
PA-18 Hydrosorb with Bungees
P/N: AD12998-S
Price: $1,045.50 each, normally sold in pairs
Eligible On: PA-18 style main landing gear
STC: N/A
FAA/PMA: N/A
Weight: 4.55 lbs. each
Installation: Same as original stock part
Misc. Info: PA-18 hydrosorb unit loaded with 1280-HDCW and 1380CW bungees
More
Cessna Control Cable Bracket
P/N: AD1550109-3
Price: $172.50 each
FAA/PMA: Approved
Material: 4130N with plating
Purpose: Direct replacement for Cessna P/N: 1550109-3.
More
Cessna Bellcrank Assembly
P/N: AD0712309-16
Price: $430 each
FAA/PMA: Pending Approval
Purpose: Direct replacement for Cessna P/N: 0712309-16.
Misc. Information: Powder coated gray.
More
Piper Aircraft Tie Down Bracket – Titanium
P/N: 3197-T
Price: $213.75 each, normally sold in pairs
Eligible On: PA-12 and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 10 oz. each
Material: Titanium with aluminum spacers.
Purpose: To remove the tie down load from the front lift strut U-channel that is attached to the front spar.
Installation: Recommended at time of wing covering.
More
Titanium Universal Cabin Heater Box
P/N: AD-18-CHB-T
Price: $585 each
Eligible On: PA-18 Series Aircraft
STC: N/A
PMA/FAA: N/A
Weight: 4.7 oz.
Material: Titanium
Installation: Mounting holes align with stock PA-18 firewall. Cable routing same as Piper PA-18 Series Aircraft.
Misc. Information: Weight savings of 3.6 oz. compared to our Stainless Steel Box (P/N AD-18-CHB).
More
Piper Titanium Carburetor Heat Box
P/N: AD15005-T
Price: $1,942.00 each
Eligible On: PA-18 and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: Titanium
Purpose: Replacement for Piper P/N 15005-00. Offers weight savings of up to 1 lb.
Installation: Same as original. Please reference Piper Owner Manual.
Misc. Information: Custom order only. Fabricated with McFarlane bearings which last much longer than the original factory bushing setup.
More
C180/185 Muffler Clamp
P/N: AD0750161-22P
Price: $92.25 per pair
Eligible On: C180 and C185
STC: N/A
FAA/PMA: N/A
More
SA460AL – STC ONLY
Click here to view SA460AL
P/N: SA460AL
Price: $273 each
Eligible On: J3C-65, J3C-65S, PA-11, and PA-11S
Purpose: Allows the installation of PA-18 pilot static system trim system.
Installation: Bolts on, will require some fabric repairs if not accomplished prior to fabric installation.
Misc. Information: Tubing called out in STC in error, should be 5052-O 3/16" OD. Sale includes STC paperwork only, no materials included.
More
SA465AL – STC ONLY
Click here to view SA465AL
P/N: SA465AL
Price: $273 each
Eligible On: J3C-65, J3C-65S
Purpose: Installs PA-18 boot cowl, windshield, and skylight.
Installation: Required welding and fabric repairs. Requires fabrication of some parts. Requires Piper drawing no. 12446 and 10561.
Misc. Information: Allows square top windshield installation. Does not allow pressure cowling installation. Sale includes STC paperwork only, no materials included.
More
PA-18-180HP Front and Rear Exhaust Stacks
P/N: AD12457-012HD-180 (front) and AD12457-013HD -180 (rear)
Price: $1,152.50 each (front) and $1,204.00 each (rear)
Eligible On: PA-18 with 180 HP conversions
STC: N/A
FAA/PMA: N/A
Weight: 5 lbs.
Material: 321 Stainless Steel
Purpose: Heavy duty front exhaust crossover stack for Piper PA-18 series with 180 HP Lycoming engines.
Installation: Same as OEM stacks.
Misc. Information: These heavy duty stacks incorporate a heavier wall thickness material than the O...
More
PA-18 Titanium Hot Rod Muffler
P/N: 3241-HRT
Price: $2,530.25 each
Eligible On: PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 2.8 lbs. for muffler (3.25 lbs. lighter than P/N 3241-HR and 3.4 lbs. lighter than P/N 3241)
Material: Titanium
Purpose: Fabricated from titanium for reduced weight. Muffler is coreless with a larger tailpipe diameter for increased horsepower.
Installation: Installation requires cutting the lower cowl tailpipe opening to clear larger tailpipe.
Misc. Informatio...
More
PA-18 Tailpipe Extension
P/N: 3241-EXT
Price: $146.00 each
Eligible On: PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 1.15 lbs.
Material: 321 Stainless Steel
Purpose: Provides a 12 inch extension for the tailpipe to help keep belly of aircraft clean.
Installation: Installs with one clamp, which is included with purchase.
Misc. Information: Fits PA-18 standard tailpipes. Does not fit Hot Rod mufflers.
More
C185 Strap
P/N: AD0750166-3HD
Price: $93.00 each
Eligible On: Cessna 185, 185A, 185B, 185C, 185D, 185E, A185E, and A185F Series Aircraft
STC: N/A
FAA/PMA: PMA Supplement No. 74
Weight: .3 oz.
Material: .0595" thick Stainless Steel
Purpose: Heavy duty replacement for Cessna P/N 0750166-3 used in Cessna Bracket Assemblies 0750166-4, 0750166-7, and 0750613-1.
Installation: Installs with 2 Monel rivets.
Misc. Information: Part is fabricated using thicker stainless steel tha...
More
Aerostop Seat Locks
P/N: AS-0001
Price: $127.25 each
Eligible On: Cessna 150 thru 210, T303, 336, and 337 Aircraft Series with McFarlane or OEM Cessna Seat Rails installed
STC: N/A
FAA/PMA: Approved
Weight: 4.3 oz. each
Material: Aluminum
Purpose: Backup seat stop for pilot an co-pilot seats.
Installation: Please see Installation Instructions.
Misc. Information: Please visit the manufacturer website for photos and additional information: Aerostop Seat Locks.
More
PA-18 Rear Exhaust Stack
P/N: AD12457-013HD
Price: $945.25
Eligible On: Piper PA-18 125 thru 150 HP
STC: N/A
FAA/PMA: Pending Approval
Weight: 4.7 lbs.
Material: 321 Stainless Steel
Purpose: Heavy duty rear exhaust crossover stack for Piper PA-18 series with Lycoming engines.
Installation: Same as OEM.
Misc. Information: Manufactured with heavier wall tubing, thicker flanges, and extra doublers to prevent cracking. Available with 180 HP extension tubes installed. ...
More
PA-18 Front Exhaust Stack
P/N: AD12457-012HD
Price: $904.00 each
Eligible On: PA-18 125 thru 150 HP
STC: N/A
FAA/PMA: Pending Approval
Weight: 4.35 lbs.
Material: 321 Stainless Steel
Purpose: Heavy duty front exhaust crossover stack for Piper PA-18 series with Lycoming engines.
Installation: Same as OEM.
Misc. Information: Manufactured with heavier wall tubing, thicker flanges, and extra doublers to prevent cracking. Available with 180 HP extension tubes installed. ...
More
Brake Disc Spacer for Cleveland Wheel and Brake Kits
P/N: 2609-DS
Price: $39.25 each
Eligible On: Cleveland 3 and 6 Bolt Wheels
STC: N/A
FAA/PMA: N/A
Weight: 2 oz.
Material: 6061 T6 Aluminum
Installation: Deflate tire, remove brake disk, insert spacer between disc and wheel, install 1/8" longer bolts, then torque to wheel manufacturer specs.
Purpose: Spaces brake disc 1/8" away from oversize tires to prevent brake caliper from rubbing.
Misc. Information: For Cleveland Kits 199-62 and 199-62A use 2609-DS-2 (same...
More
PA-18-180 Carburetor Heat Box
P/N: AD15005-180
Price: $1,622.75 each
Eligible On: Piper PA-18 with 180HP
STC: N/A
FAA/PMA: N/A
Weight: 2 lbs., 13oz.
Material: Stainless Steel
Misc. Information: Custom fabricated upon request.
More
Cessna Cabin Step (Late Models)
P/N: AD0711710-1HD (left hand) and AD0711710-2HD (right hand)
Price: $748.50 each
Eligible On: Cessna 180H thru 180K and A185E thru A185F Series Aircraft
STC: N/A
FAA/PMA: Pending Approval
Weight: 15.7 oz.
Material: 4130N, powder coated white
Purpose: Replacement for Cessna P/N's 0711710-1 and 0711710-2 used in Cessna step assemblies P/N 0711710-5 and P/N 0711710-6.
Installation: Bolt and rivet support to fuselage using fasteners as OEM part. Install your existi...
More
Airglide Brace for Ski Tunnel
P/N: AD10D2993-1
Price: $311.50 each
Eligible On: Airglide C2200, C3000, C3200, and C3600 Skis
STC: N/A
FAA/PMA: N/A
Weight: 8 oz.
Material: 4130N, powder coated silver
Purpose: Replacement for Airglide P/N 10D2993-1.
Installation: Same as original part.
More
Piper Water Rudder Tiller Bar
P/N: AD92-WS-508
Price: $49.25 each
Eligible On: Piper J3, PA-11, PA-12, PA-18, and PA-22 and Aeronca 7AC and 11AC
STC: N/A
FAA/PMA: N/A
Weight: 6.5 oz.
Material: Stainless Steel
Purpose: Replacement for EDO P/N 92-WS-508.
Installation: Same as original installation.
More
EDO 2000 Blade Brackets
P/N: AD88-W-076-1 (left hand) and AD88-W-076-2 (right hand)
Price: $75.50 each
Eligible On: Aircraft equipped with EDO 2000 floats.
STC: N/A
FAA/PMA: N/A
Weight: 4.1 oz.
Material: Aluminum
Purpose: Direct replacements for EDO PN's 88-W-076-1 and 88-W-076-2.
Installation: Same as original stock parts.
Misc. Information: Includes arm and opening for springs.
More
EDO 2000 Attach Brackets
PN: 4237-1 (lower) and 4238-1 (upper)
Price: $147.50 each for lower bracket, and $67.50 each for upper bracket
Eligible On: Aircraft equipped with EDO 2000 floats.
STC: N/A
FAA/PMA: Supplement 1 (covers lower), Supplement 1 (covers upper)
Weight: 3.5 oz. (lower) and 2.8 oz. (upper)
Material: 304 Stainless Steel
Purpose: Direct replacements for EDO P/N's 88-W-071 and 88-W-072-3.
Installation: Same as original stock parts.
More
C180 Steering Control Horn Assembly
P/N: AD16797
Price: $127.50 each
Eligible On: Cessna 180 Series Aircraft (Serial numbers 3000 thru 32151 only)
STC: N/A
FAA/PMA: N/A
Weight: 4.3 oz.
Material: Stainless Steel
Purpose: Replacement for EDO P/N 16797.
Installation: Same as original stock part.
Misc. Information: Used on early model Cessna 180 Series Aircraft without Tailwheel Steering Belcranks in Tail Cone.
More
C206 Boarding Ladder
P/N: 3193
Price: $956.00 each
Eligible On: Cessna 206 Series Aircraft equipped with EDO 582-3430 floats.
STC: SA02088AK
FAA/PMA: Supplement 1
Material: Stainless Steel support tube with Aluminum rungs.
Purpose: Used for easier loading of aircraft through right hand AFT door when aircraft is on floats.
Installation: Bolts on.
Misc. Information: Support tube is telescoping to allow for installation variances and float movement while in service.
More
C206 Water Rudder Lift Handle Kit
P/N: AD696-1182-1
Price: $385 each
Eligible On: Cessna 206 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 11.2 oz.
Material: Stainless Steel with Aluminum Brackets, powder coated black.
Purpose: Replacement for EDO P/N 696-1182-1.
Installation: Same as original stock part.
Misc. Information: Also commonly called a Water Rudder Retract Kit.
More
C170/180/185 Water Rudder Lift Handle Kit
P/N: 3359-1
Price: $399.00 each
Eligible On: Cessna 170, 180, and 185 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 12.3 oz.
Material: Stainless Steel with Aluminum Brackets, powder coated black.
Purpose: Replacement EDO P/N 5469-9.
Installation: Same as original stock part.
Misc. Information: Also commonly called a Water Rudder Retract Kit.
More
EDO 4930 Water Rudder Tillers
P/N: AD58-W-029
Price: $120.25 each
Eligible On: Aircraft equipped with EDO 4930 floats.
STC: N/A
FAA/PMA: N/A
Weight: 9.5 oz.
Material: Stainless Steel
Purpose: Replaces stock aluminum tillers, stainless steel option prevents corrosion.
Installation: Same as original stock part.
Misc. Information: Part can be used as left hand or right hand.
More
C206 Heavy Duty Muffler – Right Hand
P/N: AD1250251-13
Price: $508 each
Eligible On: Cessna 206 and 207 Series Aircraft
Weight: 3 lbs.
Material: 321 Stainless Steel
Purpose: Existing muffler repair option.
Installation: Same as original stock part.
Misc. Information: Repair station item only. Please send us your existing muffler via the carrier of your choice. Part cannot be sold without the existing muffler being sent in for repair. The existing muffler will be repaired with heavy duty core. Muffler...
More
DHC-2 Sending Unit Gasket
P/N: DHC2-SU
Price: $24.75 each
Eligible On: DHC-2
STC: N/A
FAA/PMA: N/A
Weight: .1 oz.
Material: Cork
Purpose: Seals fuel quantity sending unit.
Installation: Same as original stock part.
Misc. Information: Part is .058" thick.
More
DHC-2 Inspection Cover Gasket
P/N: DHC2-IC
Price: $19 each
Eligible On: DHC-2
STC: N/A
FAA/PMA: N/A
Weight: .2 oz.
Material: Cork
Purpose: Seals fuel tank inspection covers.
Installation: Same as original stock part.
Misc. Information: Part is .060" thick.
More
PA-20/PA-22 Axle Spacer
P/N: U1105-00
Price: $28.75 each
Eligible On: Piper PA-20 and PA-22 Series Aircraft with 1 1/2" axles
STC: N/A
FAA/PMA: N/A
Weight: 2.2 oz.
Material: 4130N
Purpose: Spaces wheel from brake caliper.
Installation: Slips on over axle.
Misc. Information: Also commonly called a Bearing Stop for 1 1/2 axle.
More
PA-18 Main Landing Gear – Limp Along
P/N: 3284-LA
Price: $475.50 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 9.5 lbs.
Material: 4130N Steel Tubing
Purpose: Used for retrieval of damaged aircraft.
Installation: Bolts on.
Misc. Information: Will fit both left and right hand sides, works for standard and 3" extended gear with 1 1/4 axles only.
More
PA-18 Exterior Paneling for Boot Cowl
P/N: AD12818-00 (left hand, rear) and AD12818-01 (right hand, rear)
Price: $57 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 11 oz.
Material: 2024 T3 Aluminum
Purpose: Serves as inspection panel between boot cowl and fuselage fabric.
Installation: Same as original stock parts.
More
PA-18 180 HP Exhaust Stack Conversion
P/N: ES-180HP
Price: $295.00 each
Eligible On: PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: Stainless Steel
Purpose: Modifies both front and rear stacks to fit 0-360 engines and comply with 180 HP STC's.
Misc. Information: Welding work is performed in our repair station. Please call us to schedule this service.
More
EDO 89-2000 Float Splash Rail Kit
P/N: FSR-KIT
Price: $289.75 per kit
Eligible On: All aircraft equipped with EDO 89-2000 floats.
STC: N/A
FAA/PMA: N/A
Weight: 2 lb., 9.2 oz. per kit
Material: 6061 T6 Aluminum, powder coated silver.
Purpose: Used to prevent propeller erosion by reducing water splash from floats.
Installation: Rivets onto floats.
Misc. Information: Parts include 4 attach angles per side.
More
DHC-2 Intensifier Funnel
P/N: ADCC2EE287ND-F
Price: $161.25
Eligible On: DHC-2 MK I
STC: N/A
FAA/PMA: N/A
Weight: 7.8 oz.
Material: Stainless Steel
Purpose: Increases ram airflow through the cabin heat intensifier tube.
Installation: Bolt onto the front end of P/N C2EE291AND.
More
EDO 2000 Water Rudder Blade Assembly
P/N: WRBA-EDO2000
Price: $409.75 each
Eligible On: All aircraft equipped with EDO 2000 floats.
STC: N/A
FAA/PMA: N/A
Weight: 2 lbs., 3 oz.
Material: Aluminum, powder coated silver.
Purpose: Owner produced replacement for EDO P/N 88-W-076-1.
Installation: Bolt on.
More
Cessna Ski Tabs
P/N: 2089-6.125
Price: $10.50 each
Eligible On: Cessna Aircraft
STC: N/A
FAA/PMA: N/A
Material: Stainless Steel
Purpose: Used to assemble rigging for ski installations.
Installation: Bolts on.
Misc. Information: Options include 2 hole, bent or 2 hole, straight tabs only.
More
Cessna Ski Washers
P/N: Order by washer size
Price: $10.50 each
Eligible On: Cessna Aircraft
Weight: Varies with washer size
Material: Stainless Steel
Purpose: Used for ski installations.
Installation: Slips onto axle.
Misc. Information: All washers are .1" thick and come in the following sizes:
1.25" ID, 2.25" OD
1.25' ID, 2.5' OD
1.375" ID, 2.25" OD
1.375' ID, 2.5' OD
1.5" ID, 2.125" OD
1.5" ID, 2.25" OD
1.5' ID, 2.5' OD
1.625' ID, 2.25 OD
1.625' ID, 2....
More
PA-18 Fairing – Wing, Lower AFT
P/N: AD12275-00 (left hand) and AD12275-01 (right hand)
Price: $91.00 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1 (covers left hand), Supplement 1 (covers right hand)
Weight: 4.6 oz.
Material: 2024 T3 Aluminum
Purpose: Direct replacement for Piper PN's 12275-00 and 12275-01.
Installation: Same as original stock part.
Misc. Information: Part supplied as bare aluminum with tab and screw included. This part will not fit if wing f...
More
PA-18 Fairing – Wing, Lower Center
P/N: AD12274-00 (left hand) and AD12274-02 (right hand)
Price: $47.25 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1 (left hand), Supplement 1 (right hand)
Weight: 5.3 oz.
Material: 2024 T3 Aluminum
Purpose: Direct replacement for Piper PN's 12274-00 and 12274-02.
Installation: Same as original stock part.
Misc. Information: Part supplied as bare aluminum.
More
PA-18 Fairing – Plate Attachement
P/N: AD11719-00 (left hand) and AD11719-01 (right hand)
Price: $95.75 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1 (left hand), Supplement 1 (right hand)
Weight: 1.9 oz.
Material: 2024 T3 Aluminum
Purpose: Direct replacements for Piper P/N's 11719-00 and 11719-01.
Installation: Same as original stock part.
Misc. Information: Part is supplied as bare aluminum. This part will not fit if wing flaps are extended to fuselage.
...
More
PA-18 Fairing – Leading Edge
P/N: AD12276-00 (left hand) and AD12276-01 (right hand)
Price: $116.25 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1 (covers left hand), Supplement 1 (covers right hand)
Weight: 5.3 oz.
Material: 2024 T3 Aluminum, powder coated white.
Purpose: Direct replacement for Piper P/N's 12276-00 and 12276-01.
Installation: Same as original stock part.
Misc. Information: Comes with rubber chafing strip installed.
...
More
PA-18 Fairing – Wing Top
P/N: AD11523-00
Price: $59.75 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1
Weight: 9 oz.
Material: 2024 T3 Aluminum
Purpose: Direct replacement for Piper P/N 11523-00.
Installation: Same as original stock part.
Misc. Information: Part is supplied as bare aluminum with nut plate and angle installed. This part will not fit if wing flaps are extended to fuselage.
More
PA-18 Control Knobs
P/N: 3311 (Blank), 3312-1 (Mixture), 3312-2 (Carb. Heat), 3312-3 (Cabin Heat/Vent), 3312-4 (Rear Seat Heat), 3312-5 (Windshield Heat/Defrost), and 3312-6 (Fresh Air)
Price: $11 each
Eligible On: Piper PA-18 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1 (covers Blank and Mixture), Supplement 1 (covers Blank and Cabin Heat/Vent)
Weight: .5 oz.
Material: Plastic knob with brass threads.
Purpose: 3311 and 3312-1 are direct replacements for Piper P/N 471-053; 3311 and ...
More
PA-12 Stainless Steel Firewall
P/N: 12-SSFW
Price: $595.25 each
Eligible On: Piper PA-12 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 5.5 lbs.
Material: Stainless Steel
Purpose: Replacement firewall.
Installation: Same as original stock part. Requires riveting.
Misc. Information: Our Stainless Steel Firewalls are built to order using your old firewall as a template for correct opening locations. A flange is formed around the edges to stiffen the firewall and allow for easier boot cowl f...
More
PA-12 Titanium Firewall
P/N: 12-TFW
Price: $917.50 each
Eligible On: Piper PA-12 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: approximately 3 lbs.
Material: Titanium
Purpose: Lightweight Firewall option compared to Stainless Steel.
Installation: Same as original stock part. Requires riveting.
Misc. Information: Our Titanium Firewalls are built to order using your old firewall as a template for correct opening locations. A flange is formed around the edges to stiffen the firewall an...
More
Piper Aircraft Tie Down Loop
P/N: 3218-1
Price: $57.25 each
Eligible On: Piper J3, J4, J5, PA-11, PA-12, PA-14, PA-16, PA-18, PA-19, PA-20, and PA-22 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1
Weight: 2.3 oz.
Material: 4130N, powder coated white
Purpose: Direct replacement for Piper P/N 12345-04.
Installation: Please see Installation Instructions.
Misc. Information: Please see our Engineering Design Approval for more information regarding this replacement part.
More
DHC-2 Boarding Ladder
P/N: ADC2FS3581ND (left hand) and ADC2FS3582ND (right hand)
Price: $705.50 each
Eligible On: DHC-2 Beaver
STC: N/A
PMA/FAA: N/A
Weight: 2 lbs., 3 oz.
Material: 4130N, powder coated white.
Purpose: Boarding ladder for Landplane.
Installation: Same as original stock part, bolt on installation.
More
Piper Main Landing Gear – 6″ Extended Length with 1 1/2 Axle
P/N: 3284-6X1A (left hand) and 3284-6X2A (right hand)
Price: $617.50 per side
Eligible On: Piper PA-12, PA-14, and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: 4130N Steel Tubing
Purpose: Heavy duty gear provides additional clearance for propeller on aircraft equipped with smaller tires or ski’s. Also allows for take off with lower air speed.
Misc. Information: Main Landing Gear can be powder coated white, black, or gray for an additional $93 per side. Gea...
More
Piper Main Landing Gear – 6″ Extended Length with 1 1/4 Axle
P/N: 3284-6X1 (left hand) and 3284-6X2 (right hand)
Price: $617.50 per side
Eligible On: Piper PA-12, PA-14, and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: 4130N Steel Tubing
Purpose: Heavy duty gear provides additional clearance for propeller on aircraft equipped with smaller tires or ski’s. Also allows for take off with lower air speed.
Misc. Information: Main Landing Gear can be powder coated white, black, or gray for an additional $93 per side. Gear ...
More
Piper Main Landing Gear – Standard Length with 1 1/2 Axle
P/N: 3225-A1 (left hand) and 3225-A2 (right hand)
Price: $535.50 per side
Eligible On: J3, PA-11, PA-18, and PA-19 Series Aircraft
STC: N/A
FAA/PMA: Supplement 1
Weight: 8.4 lbs. per side
Material: 4130N Steel Tubing
Purpose: Heavy duty replacement for Piper P/N’s 00041-60/61, 10033-00/01, and 10033-051/06.
Installation: Same as stock landing gear.
Misc. Information: Main Landing Gear can be powder coated white, black, or gray for an additional $93 per side. ...
More
C180 V-Brace
P/N: 180-VBE
Price: $672.00 each
Eligible On: Cessna 180, 180A, and 180B with serial numbers 604, 613, and 3000 thru 50661.
STC: SA02319AK-D
FAA/PMA: Supplement 5
Weight: 2 lbs., 3.7 oz.
Material: Stainless steel, powder coated black.
Purpose: Windshield V-Brace adds rigidity to the airframe when on floats or rough terrain.
Installation: Please see Installation Instructions.
More
Piper Shock Struts – 6″ Extended Length
P/N: 3164-5 (PA-18) and 3164-6 (PA-12 and PA-14)
Price: $175 each
Eligible On: Piper PA-12, PA-14, and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: 4130N, powder coated white, black, or gray.
Purpose: Required for 6" Extended Length Main Landing Gear installations.
Installation: Same as original stock part.
Misc. Information: Custom fabricated upon request.
More
206/207/210 Rudder Bar – Right Hand
P/N: AD1260558-2
Price: $2,065.50 each
Eligible On: Cessna 206, U206G, TU206G, 206H, T206H, 207A, T207A, 210-5, and 210-5A Series Aircraft
STC: N/A
FAA/PMA: Supplement 35
Weight: 1.8 oz.
Material: 4130 N, powder coated black
Purpose: Direct replacement for Cessna P/N's 1260558-2 and 1260418-4.
Installation: Same as original stock part.
Misc. Information: Reinforcement straps installed on pedal tubes.
More
PA-22 30.5 Gallon Fuel Tank
P/N: 3258-L (left hand) and 3258-R (right hand)
Price: $3,415.00 each side
Eligible On: Piper PA-22-150 and PA-22-160
STC: SA00092SE
FAA/PMA: Supplement 1
Weight: 12 lbs. per pair, empty
Material: Aluminum
Purpose: Allows up to 61 gallons of fuel capacity.
Installation: Please see Installation Instructions.
Misc. Information: Must install both left hand and right hand tanks. Fuel system sight gauge (P/N 3286) is required for installation.
More
PA-12 and PA-14 30.5 Gallon Fuel Tank
P/N: 3140-516-L (left hand) and 3140-516-R (right hand)
Price: $3,415.00 each side
Eligible On: Piper PA-12, PA-12S, and PA-14
STC: SA5781NM
FAA/PMA: Supplement 6
Weight: 12 lbs. per pair, empty
Material: Aluminum
Purpose: Allows up to 61 gallons of fuel capacity.
Installation: Please see Installation Instructions.
Misc. Information: Must install both left hand and right hand tanks. Fuel system sight gauge P/N 3286 is required for installation.
More
Float Pulley Clamp
P/N: AD-C-750
Price: $10.25 each
Eligible On: Steel tube fuselages with 3/4" diameter lower longerons
STC: N/A
FAA/PMA: N/A
Material: Stainless Steel
More
Piper Cabane Vee
P/N: 3166-2
Price: $420.75 each
Eligible On: PA-12 and PA-14 Series Aircraft
STC: SA4616NM (covers PA-12) SA4617NM (covers PA-14)
FAA/PMA: Supplement 1
Weight: 2.2 lbs.
Material: 4130N
Purpose: Heavy duty Cabane Vee modified for use on PA-12 and PA-14 Series Aircraft with PA-18 style landing gear installed.
Installation: Installed per Roger Borer STC SA148AL. His daughter Karen maintains his STC's. She can be reached at (907) 317-7732. An additional weld on fit...
More
Piper Main Landing Gear Safety Cables – Wide Body
P/N: 3344-4W
Price: $210.50 per kit
Eligible On: PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: Stainless steel plates and galvanized cables.
Purpose: Prevents main landing gear from collapsing should a landing gear component fail.
Installation: Please see Installation Instructions. It is recommended to use new AN hardware when installing new safety cables due to bolt length. Bolt kits available upon request for $24.75 each.
Misc. Information: Custom fabr...
More
Piper Main Landing Gear Safety Cables – 6″ Extended Length
P/N: 3344A-6X (PA-12) or 3344-6X (PA-18)
Price: $210.50 per kit
Eligible On: PA-12 and PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Purpose: Prevents main landing gear from collapsing should a landing gear component fail.
Installation: Please see Installation Instructions. It is recommended to use new AN hardware when installing new safety cables due to bolt length. Bolt kits available upon request for $24.75 each.
Misc. Information: Custom fabricated lengths availa...
More
Piper Weld On Rear Shoulder Harness Attach Bracket
P/N: 3232W-2
Price: $73.50 each
Eligible On: PA-12, PA-12S, PA-18, PA-18S, PA-19, and PA-19S Series Aircraft
STC: SA02488AK
FAA/PMA: Supplement 54
Weight: 5.4 oz.
Material: 4130N
Purpose: Attaches shoulder harness to fuselage frame.
Installation: Please see Installation Instructions.
Misc. Information: STC sold separately for $289.75 each.
More
PA-18-150 Tailwire Support
P/N: AD60764-2
Price: $68.50 each
Eligible On: PA-18-150 with serial numbers 18-8602 thru 18-8109013, 1809001 thru 1809057, and 1809060
STC: N/A
FAA/PMA: N/A
Material: .062 4130N
Purpose: To comply with Piper Service Bulletin 706B and Airworthy Directive 81-06-08
Installation: Please see SB 706B for installation instructions.
Misc. Information: Part fabricated in accordance with Piper Service Bulletin 706B
More
Cessna Stabilizer Trim Jack Screw Boot
P/N: U0712500-18
Price: $64.75 each
Eligible On: Cessna 180, 182 thru 182D, and 185 Series Aircraft
STC: N/A
PMA: Supplement 41
Purpose: Direct replacement for Cessna P/N 0712500-18. Covers and prevents debris from interfering with jack screws.
Installation: Installed when jack screws are removed for repair.
More
PA-18 Lift Strut Reinforcment Bracket
P/N: 3192-18
Price: $128.50 each
Eligible On: PA-18 Series Aircraft
STC: SA02026AK
FAA/PMA: Supplement 9
Weight: 4 oz.
Material: 4130N Steel
Purpose: Provides additional strength to the lift strut attach brackets and helps prevent damage from high winds when aircraft is tied down outdoors.
Installation: Please see Installation Instructions.
Misc. Information: Powder coated white. If lift strut fitting is bent or has elongated holes it will need to be replaced...
More
PA-18 Titanium Boot Cowl Assembly
P/N: 18-BC-T
Price: $2,348.75 each
Eligible On: PA-18 Series Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 8.875 lbs.
Material: Titanium
Misc. Information: F. Atlee Dodge boot cowls are fabricated using our FAA/PMA approved firewall. We incorporate reinforcements at the cowl channel attach points to prevent cracking. Cowl channel kit is installed. Side to top seams are left un-riveted to allow for adjustable fit to fuselage.
More
C170/180 Ski Attach Kit
P/N: 3168-180
Price: $490.00 per kit
Eligible On: All Cessna 170 Series Aircraft as well as early model Cessna 180 Series Aircraft prior to S/N 51313.
STC: SA02360AK
FAA/PMA: Supplement 29
Material: 304 SS
Purpose: Used for ski rigging installation.
Installation: Brackets are bolted on. See copy of installation instructions here: INSTALLATION INSTRUCTIONS
Misc. Information: Commonly used for straight wheel ski replacement installations under FAA field approval....
More
C180/185 Ski Attach Kit
P/N: 3168-185
Price: $490.00 per kit
Eligible On: Late model Cessna 180 Series Aircraft with S/N# 51313 and on as well as all Cessna 185 Series Aircraft.
STC: SA02360AK (covers C180 only)
FAA/PMA:Supplement 29 (covers C180 only)
Material: 304 SS
Purpose: Used for ski rigging installation.
Installation: Brackets are bolted on. See copy of installation instructions here: INSTALLATION INSTRUCTIONS
Misc. Information: Commonly used for straight wheel ski replacement ...
More
DHC-2 Hydraulic Tank (Post Mod)
P/N: ADC2US1185A
Price: $1,404.00 each
Eligible On: DHC-2 Ski Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 26 oz.
Material: 6061-T6 Aluminum
Purpose: Fuselage hydraulic reservoir for ski installations.
Installation: Same as original installation.
Misc. Information: Used on DHC-2 Post Mod 2/1328. Custom fabricated. Drawing on file at F. Atlee Dodge. Please see P/N ADC2US761A for Pre Mod 2/1328 tank.
More
DHC-2 Hydraulic Tank (Pre Mod)
P/N: ADC2US761A
Price: $945.25 each
Eligible On: DHC-2 Ski Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 26 oz.
Material: 6061-T6 Aluminum
Purpose: Hydraulic reservoir for ski's.
Installation: Installs in wing root forward of front spar.
Misc. Information: Used on DHC-2 Pre Mod 2/1328. Custom fabricated. Drawing on file at F. Atlee Dodge. Please see P/N ADC2US1185A for Post Mod 2/1328 tank.
More
PA-12 Weld On Aft Float Fittings
P/N: 3143
Price: $803.25 per pair
Eligible On: PA-12 and PA-14 Aircraft Series
STC: SA00132SE
FAA/PMA: Supplement 11
Weight: 2 lbs. per pair
Material: 4130N Steel
Purpose: Replaces clamp on style fittings. Provides cleaner and stronger installation.
Installation: Normally accomplished at the time of re-build, however, the fabric can be removed to accommodate installation at other times.
Misc. Information: Part includes swivel block for strut and swivel wire p...
More
PA-18 Cowl Channel Attach Kit
P/N: 18BC-CCAK
Price: $137.25
Eligible On: PA-18
STC: N/A
FAA/PMA: N/A
Weight: 3.5 oz.
Material: 304 Stainless Steel
Purpose: Used to attach cowl channels to boot cowl.
Installation: F. Atlee Dodge has added a back up angle to each location that is installed on the AFT side of the firewall. They are riveted or bolted onto the boot cowl skins to prevent the firewall from cracking. Kit includes 2 upper angles, 2 lower angles, and 2 lower back up angles. Click here...
More
Piper Muffler
P/N: AD10308-003
Price: $803.25 each
Eligible On: PA-12, PA-14, PA-16, PA-22, and PA-25 (S/N 722 and up) Series Aircraft
STC: N/A
FAA/PMA: N/A
Material: Stainless steel
Purpose: Exhaust system muffler.
Installation: Same as stock muffler installation.
Misc. Information: Supersedes P/N's 10308-000, 10308-003, 10308-00 and 10308-03. Repair station item only. Please send us your existing muffler via the carrier of your choice. Part cannot be sold without the exist...
More
PA-12 Firewall Blanket
P/N: AD12-FW-BLKT
Price: $205 each
Eligible On: PA-12 and PA-14 Aircraft Series
STC: N/A
FAA/PMA: N/A
Weight: 13 oz.
Material: Fabric is Naugahyde with fire block foam backing that self extinguishes and is also gas, grease, and oil resistant. Naugahyde material meets MUSS-302 flammability requirements. Foam backing meets UL-91 HF-1 flammability requirements. Fabric rated to -40 below.
Purpose: Insulates firewall to reduce heat transfer and noise in the cabin.
In...
More
DHC-2 Tiller Bar for Landplane
P/N: AD-C2UT479A
Price: $202.25 each
Eligible On: DHC-2 Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 8 oz.
Material: 6061 T6
Purpose: Allows tailwheel assembly to be connected to rudder cables.
Installation: Same as original installation.
Misc. Information: Powder coated gloss white. Custom fabricated per customer request. Drawing on file at F. Atlee Dodge.
More
DHC-2 Tiller Bar for Seaplane
P/N: AD-C2UT479A-4930
Price: $248.50 each
Eligible On: DHC-2 Aircraft
STC: N/A
FAA/PMA: N/A
Weight: 13 oz.
Material: 6061 T6
Purpose: Connects air rudder to water rudder.
Installation: Same as original installation.
Misc. Information: Powder coated gloss white. Custom fabricated per customer request. Drawing on file at F. Atlee Dodge.
More
***MANDATORY SERVICE BULLETIN***
There was a recent mailing from the FAA to our customers who previously purchased Removable Cessna Jump Seats. Should you receive this letter please visit this link for more information.
More
DHC-3 Hydraulic Tank
P/N: ADC3S23-15
Price: $967.00 each
Eligible On: DHC-3
STC: N/A
FAA/PMA: N/A
Weight: 22 oz.
Material: 6061 T6 Aluminum
Purpose: Used for wheel ski installation on DHC-3 only.
Installation: To be installed at the same time as skis.
Misc. Information: Custom fabricated as per customer request. Drawing on file at F. Atlee Dodge.
More
PA-18 Support Rod
P/N: 3241-16
Price: $57.25 each
Eligible On: PA-18 Series Aircraft
STC: SA02273AK
FAA/PMA: Supplement 2
Material: 304 Stainless Steel
Purpose: Tailpipe support rod for PA-18 Hot Rod Muffler.
Installation: Replaces Piper P/N 13003-00.
Misc. Information: For use with PA-18 Hot Rod Muffler (P/N 3241-HR) and 3" clamps without pin (P/N AD-C-3000). 1 rod is needed per exhaust.
More
Silver Ski Springs
P/N: 2097
Price: $193.00
Eligible On: Approved Model List
STC: SA4624NM
FAA/PMA: Supplement 1
Weight: 2.2 lbs.
Material: Cadmium Plated Steel
Purpose: Improves ski rigging tension in cold weather.
Installation: Installation instructions included with STC.
Misc. Information:
For ski equipped airplanes that have rigid welded tubular steel type main landing gear
VNE equal to 160 MPH or less
Maximum weight 2500 lbs.
16 1/2" long, 1 5/6" diameter
More
DHC-2 Seat Belt Tie Down / Cargo Attach Anchors
P/N: 3181
Price: $857.75 each
Eligible On: DHC-2 MK.1
STC: SA3617NM
FAA/PMA: Supplement 1
Purpose: Allows seat belts and/or cargo anchors to be installed in cabin floor.
More
DHC-2 Folding Center Row Seat
P/N: 3180
Price: $4,166.50 each
Eligible On: DHC-2 MK.1
STC: SA4613NM
FAA/PMA: Supplement 1
Purpose: To allow for a 3 person middle row bench seat.
Installation: Seat snaps in using standard attach brackets. Fits into original seat bases. Must have seat belt/cargo anchors installed in floor in accordance with STC SA3617NM.
Misc. Information: Bench can be split to allow for a single seat at times. You can order the bench with a single seat on the left or right. Yo...
More
Mandatory Service Bulletin Jump Seat Kit
P/N: 3187-MSBKIT (full kit for 1 pair of seats) and/or 3187-MSBKIT2 (half kit for only 1 seat)
Price: $131.25 per full kit, $65.50 per half kit.
Eligible On: C170, C172, C175, C180, C182, and C185 Series Aircraft
STC: SA02008AK
FAA/PMA: Supplement 1
Purpose: To ensure existing jump seats comply with MSB 3187-I-01 rev A.
Full Kit Includes:
Copy of Mandatory Service Bulletin (MSB 3187-I-01 rev A)
Copy of Airplane Flight Manual Supplement (AFMS 3187)
Copy of I...
More
PA-18 Folding Front Seat – STC and Install Kit ONLY
P/N: 3186-Kit or 3186-Install
Price: $420.75 uninstalled, $1,021.75 installed
Eligible On: PA-18 and PA-19 Series Aircraft
STC: SA02085AK
FAA/PMA: Supplement 1
Material: 4130 N
Purpose: Allows existing pilot seat to be modified into a folding seat for easier loading of aircraft.
Installation: Weld on modification to existing seat.
Misc. Information: If you would like F. Atlee Dodge to install this kit for you, please send us your existing seat.
More